If you’re interested in learning how to hang pegboard on your shop or craft room wall, you’ve come to the right place! I don’t know about you, but I can’t think, let alone work, when I’m surrounded by chaos. Weird fact about me: I actually like to clean and organize my shop before I start cutting wood. Strange, I know. But, I find that it is nice to start a project in a clean, organized environment. The creative juices just flow better.
I don’t have a lot of hand tools. But, my collection is growing enough that my cabinet was getting a little crowded and it was difficult to find things. I’ve been wanting to hang pegboard on the wall for some time now. But it’s just one of those things that is easy to put off.
Seriously though, isn’t this wall just screaming for pegboard?
When I finally got motivated enough, I headed to Lowe’s and found the pegboard aisle. I was all by myself and found the huge 4′ x 8′ sheet of pegboard. Not super heavy, but rather flimsy and awkward to carry. My plan was to have someone cut it to size at the store. But sadly, the saw was broken that day! So, I went home without my pegboard because there was no way I could fit a 4′ x 8′ sheet in my Jeep.
Moral of the story. Have the nice guys at the home improvement store cut your pegboard to size. They usually do it for free. Hopefully the saw is functioning the day you go! While you’re at it, have them cut 2 pieces of 1×3″ the width of the pegboard.
A few days later, hubby and I went to visit my in-laws. My dad-in-law, who is a mega handy man, said he had some wood scraps he was going to throw away. He asked me if I wanted to go through them. Among the scraps was -lo and behold- a piece of pegboard close enough to the size I needed!. Woot! I love free stuff.
How to Hang Pegboard
Affiliate links included for your convenience. Click here to read the full disclosure
Materials Needed- To Hang
- Pegboard Cut to size. Mine was 2′ x 4′. Small enough to hang it with no help.
- Cut a 1″x 3″x 8′ into 2 pieces equal to the same width of the pegboard. Mine were 2′ each.
- Stud Finder
- 2-1/2″ Wood Screws
- Pegboard Hooks
Materials Needed- To Frame
- (2) 8′ long primed 1×2″ boards . Cuts are 2@ 4′ and 2@ 26 1/4″ for the sides.
- (2) 8′ long 1″ wood trim of your choice. Measure as you go for more precise cuts.
- Wood Glue
- Nail Gun
- Miter saw
- Paint of choice
Step 1: Mark Studs and Hang the Support Boards
Use a level to make sure your board doesn’t end up crooked.
The two boards should be spaced to match the height of the pegboard. In my case, that was 25″ from the top edge of the top piece to the bottom edge of the bottom piece.
If you are hanging a larger piece of pegboard, you will want to add some vertical support as well.
Hanging the support boards gives you a solid surface to attach the pegboard, and also allows for some dead space behind it. You want the board to stick out of the wall to leave space for hooks.
Step 2: Attach Pegboard
Using shorter wood screws this time (I used 1- 1/4″) attach the pegboard to the 1×3’s. I used two screws in each corner.
Pretty quick, huh?
The Snowball Effect
Initially, hanging this pegboard, as you see it, was all I was aiming for. As I was about to start hanging my tools, I noticed all the dings and water damage on the board (see that shadow on the left?). I also wasn’t pleased that I could see the dead space behind it, when looking from the side. So, I decided to dress it up and make it look prettier.
Step 3- Framing (optional)-
For my 2′ x 4′ frame the 2 vertical pieces were 27 1/4″ and the 2 horizontal pieces were 4′. I would recommend you measure as you go for more precise cuts.
I kept the edges blunt, but you could miter them if you’d like!
Adding the Trim
Again, I was going to leave it as it, BUT, the chipped edges of the board were bugging me! So, I attached 1″ trim (yep, back to Lowes) with wood glue and brad nails.
I mitered the edges this time. But it wasn’t too bad! I basically just did my first edge at a 45 degree angle on the miter saw, then held my trim on the pegboard and marked my cut for the opposite end. Luckily, my saw was sitting right next to this project, so it was pretty convenient!
Step 4: Paint and Dress it Up
Now all that is left to do is give the whole thing a fresh coat of paint, put your pegboard hooks on and behold, your tools are organized!
Now the hardest part. Go DO IT! 🙂
I have a very small basement shop. I wish I could have fit a whole sheet of pegboard. I’m happy with any extra storage, though!
Pin this for later!
Novice woodworker and serial Popcorn eater, Janice Thomas writes detailed tutorials that motivate others to “dare to try”. Originally from Puerto Rico, Janice is fluent in Spanish and dreams of owning a beach house on the island someday! Janice currently lives in Utah with her husband and children, where she works as a university professor.